Correction to: Practical framework for data-driven RANS modeling with data augmentation

Acta Mechanica Sinica -     

A New Sufficient Degree Condition for a Graphic Sequence to Be Forcibly k-Edge-Connected

A graphic sequence π =(d₁, d₂,..., d_n) is said to be forcibly k-edge-connected if every realization of π is k-edge-connected. In this paper, we obtain a new sufficient degree condition for π to be forcibly k-edgeconnected. We also show that this new sufficient degree condition implies a strongest monotone degree condition for π to be forcibly 2-edge-connected and a conjecture about a strongest monotone degree condition for π to be forcibly 3-edge-connected due to...     

A note on statistical analysis of factor models of high dimension

Science China Mathematics - Linear factor models are familiar tools used in many fields. Several pioneering literatures established foundational theoretical results of the quasi-maximum likelihood...     

Integral Representations of the Large and Little Schröder Numbers

In the paper, the authors establish several integral representations for the generating functions of the large and little Schröder numbers and for the large and little Schröder numbers.     

陶瓷基功能材料载体纤维增强效果及机理

以陶瓷基功能材料载体为研究对象,按照其生产工艺配方,研究了纤维种类(莫来石、氧化铝、氧化锆)及其添加量对陶瓷基功能材料载体性能的影响.在相同实验条件且不影响其功能化参数前提下,将其与未添加纤维的空白试样力学性能进行对比.结果表明,试样经1200℃烧成后,相比莫来石与氧化铝纤维增强的陶瓷基功能材料载体,氧化锆纤维的增强效果最好.当氧化锆纤维的添加量为0.8 wt;时,试样的吸水率和气孔率均较低,分别为2.0;、4.0;,相比空白对比试样抗折强度增强了42.4;.     

氨基功能化磁性CoFe2O4/氧化石墨烯去除电镀废水中Cr(Ⅵ)的研究

使用改良的hummers法制备出的氧化石墨烯为载体,采用共沉淀法制备出磁性CoFe2O4/氧化石墨烯(MGO),再使用三乙烯四胺(TETA)对磁性CoFe2O4/氧化石墨烯进行氨基功能化,制备出氨基功能化磁性CoFe2O4/氧化石墨烯吸附剂.采用X-射线衍射仪(XRD)、傅里叶变换红外光谱仪(FT-IR)和扫描电子显微镜(SEM)对TETA-MGO的物相、化学组成和微观形貌进行表征,以TETA-MGO作为吸附剂去除电镀废水中Cr(Ⅵ),探讨吸附性能和吸附机理,分析TETA-MGO在外加磁场下的液固分离和再生吸附性能.结果表明纳米级立方尖晶石相磁性CoFe2O4均匀生长于氧化石墨烯的表面和片层之间,TETA通过C-N键与磁性氧化石墨烯(MGO)相连,氨基功能化成功,活性吸附位点增点.室温下,pH =2时吸附效果最佳,吸附120 min时达到吸附平衡,平衡吸附量约为48.66 mg·g-1,TETA-MGO对Cr(Ⅵ)的吸附动力学和吸附热力学可分别使用拟二级动力学模型和Langmuir等温吸附模型描述,吸附过程主要属于化学吸附控制的单分子层吸附,使用外加磁场可以对TETA-MGO实现简单的固液分离,TETA-MGO经过6次再生吸附后,对Cr(Ⅵ)的吸附量仅下降19.67;,说明具有良好的循环再生吸附能力.     

Synthesis of Small‐Sized,Porous, and Low‐Toxic Magnetite Nanoparticles by Thin POSS Silica Coating

In this communication, we report the synthesis of small‐sized (<10 nm), water‐soluble, magnetic nanoparticles (MNPs) coated with polyhedral oligomeric silsesquioxanes (POSS), which contain either polyethylene glycol (PEG) or octa(tetramethylammonium) (OctaTMA) as functional groups. The POSS‐coated MNPs exhibit superparamagnetic behavior with saturation magnetic moments (51–53 emu g^?1) comparable to silica‐coated MNPs. They also provide good colloidal stability at different pH and salt concentrations, and low cytotoxicity to MCF‐7 human breast epithelial cells. The relaxivity data and magnetic resonance (MR) phantom images demonstrate the potential application of these MNPs in bioimaging.     

A post curing strategy toward the feasible covalent adaptable networks in polyacrylate latex films

The implementation of covalent adaptable networks (CANs) in general resin system is becoming attractive. In this work, we propose a simple post-curing strategy based on the core-shell structured acrylate latex for the achievement on both the improved general performance and the CANs characteristics in latex films. The building to the CANs was relied on the introduction of 4,4′-diaminophenyl disulfide as the curing agent, which cured the acetoacetoxy decorated shell polymer through the ketoamine reaction. The metathesis reaction of aromatic disulfides in the crosslinking segments enabled the thermally induced dynamic behavior of the network as revealed in the stress relaxation tests by comparison with other diamine crosslinking agents without the incorporation of disulfide. The synergism of the dynamic crosslinking of the shell polymer and static crosslinking in the core polymer contributed to the improved mechanical strength (15 MPa, strain% = 250%) and the suppressed water adsorption (~1% in 24 h of soaking) of the latex film, which exhibited above 90% of recovery in both strength and strain from a cut-off film damage within 1 h at 80°C. Moreover, the cured latex film could be recycled, and 75% of the mechanical performance was regained after three fragmentation-hot-pressing cycles. These, in addition with the feasible and environmental friendly characteristics, suggest a sustainable paradigm toward the smart thermosetting latex polymers.